Regenerative Practice in Australian wood firing – transforming a small kiln Bandicoot Pottery
Updated: Oct 29
Regenerative Practice in Australian wood firing – transforming a small kiln
Bandicoot Pottery
Daniel Lafferty and Gabrielle Powell January 2026
What does it entail?
Following the complete losses incurred during the Black Summer, including the destruction of the studio and most of its equipment, which was subsequently sold as scrap metal and disposed of in a landfill, some remnants remained in the studio’s front yard and seemed like potters waste. Approximately twelve months later, Gabrielle initiated the idea of purchasing a new electric kiln, only to realise that we possessed valuable waste material in the yard.
While the cost of purchasing a new electric kiln of the desired size exceeded her budget, renovating the existing Woodrow electric kiln that lay forgotten in the yard presented a more economical option. However, this renovation would necessitate the replacement of the computer programming box and burnt-out wiring. This kiln would serve as our primary kiln for pottery classes and required a substantial overhaul.
The representatives from AA kilns Sydney were exceptionally helpful and provided a rehabilitated controller box, which they described as the worst they had ever encountered, filled with melted plastic and burnt wires. Consequently, with their help we decided to revive the old Woodrow once again and restore it to a functional electric kiln.
Daniel possesses a passion for repairing old items and restoring them to their former glory, which motivated this endeavour. The kiln underwent a comprehensive overhaul, both on the exterior and interior, resulting in a fresh new appearance.
This prompted us to re-consider the other two waste-land kilns still present in the studio paddock. One was a large Woodrow electric kiln 14 cubic foot, while the other was a 30-cubic-foot gas port-a-kiln. Both kilns had been through the black summer bushfires and were never going to be functional again. The large Woodrow kiln exhibited significant deterioration on its exterior, while the internal brickwork remained in a reasonable condition, making it a viable candidate for restoration. The fibre port-a-kiln possessed high-quality stainless-steel sheeting on its exterior and metalwork, but the interior was severely damaged, with fibre falling in from time spent weathering, and lots of rust.
Daniel proceeded to dismantle this kiln to gather the necessary resources for the rehabilitation of the Woodrow kiln. He meticulously saved every component, including ceramic threaded rods, pieces of stainless-steel cladding, and any other useful materials. This collection provided him with an ample supply of materials to commence and complete the restoration process.
One of the most critical tasks was to repair the Woodrow door, which had rusted off at the top hinge and was in a precarious state. It could not be opened without the support of a trolley jack. Daniel was eager to retain the swinging door as this is a luxury on any kiln especially a wood fired kiln! The metal sheeting holding the floor up had severely disintegrated, posing a risk of the floor falling through. This was a priority to repair and stabilise the kiln structure. The main frame of the kiln was in reasonable condition and only required the front top piece of angle iron to be reinforced. Therefore, Daniel proceeded to undertake these tasks one at a time over a three-month period.
New channel iron was folded up at a metal fabrication shop for the top half of the door. He proceeded to cut off the channel iron that surrounds the bricks on the door. Subsequently, some bricks needed replacement around the edge, and the outer insulation required repairs as well.
Daniel retrieved an insulation sheet from the back of the controller box when it was removed. The new channel iron was placed around the door once the brickwork was satisfactory, and it was welded into place, restoring the functionality of the top hinge.
Upon removing the metal, these doors proved to be extremely fragile and prone to falling apart. To secure the brickwork during the process, he employed tie-down straps wrapped around the brick work to hold everything in place. Once the metal had been replaced, the door regained its rigidity and stability. Subsequently, with the remaining cladding removed, Daniel observed the supporting steel straps that held the kiln structure together. He carefully navigated around these straps to devise a plan for installing air holes, a stoke hole, and some exit flues.
The kiln is constructed from a very soft and friable material, necessitating utmost care when cutting holes. The outer cladding could be cut using a scraper as a blade while a masonry drill was employed to remove the bricks for the locations of the flue, stoke, and air inlets. An old pruning saw was utilised to cut through the soft bricks and restore a straight edge.
Next, he constructed a steel platform capable of supporting the weight of a small chimney made from RI bricks. The chimney stands at a height of 1.8 metres and has been reinforced with an angle iron frame, skilfully constructed with help of our capable daughter.
In the design rather than constructing a bag wall, Daniel opted to build a wall in front of the flues, forcing the flame to rise high within the chamber and potentially achieving a more even temperature distribution. This back wall, known as a stammer, is typically perforated, but he allowed the gaps where the elements run to provide additional ventilation on the sides. The lower corners were cut off the shelf forming this wall to allow some heat to pass through, aiming to prevent a cold spot. This wall was constructed using a kiln shelf and secured with threaded ceramic rods retrieved from the port-a-kiln, drilling and screwed to the wall to hold the shelf in place on its edge. The flue sizes were estimated, and there were also limitations on size due to the back of the kiln structure it was cut out without compromising its integrity.
Due to the small size of the kiln, everything was carefully measured. The firebox measures 51 cm x 20 cm (20 x 8 in), with two flue outlets measuring 13 cm x 11 cm (5 x 4.5 in) and the chimney internal measuring 11 cm x 51 cm (4.5 x 20 in). There was no formal plan; instead, the construction was guided by intuition and the available materials.
Anticipation was building for the first test firing. Although we had to relocate the kiln to its intended position, despite referring to it as a “port-a-kiln wood,” it proved to be extremely heavy to move. Daniel utilised our reliable bobcat and chains to transport it from the work shed to the pottery studio. He estimated the weight of the kiln at 1.5 or more tonne as the bobcat easily lifts a tonne of clay but struggled to move this kiln.
Once in position, firing one was a bisque firing with rocks for sintering in the bottom and pots for bisquing. The firing temperature was Cone 06 1000° Celsius. To start the firing Daniel would open the door to stoke the firebox gently placing the wood in until 400° Celcius was achieved and there was a bed of charcoal. Then he used the small stoke hole and left the door closed for the rest of the firing. This firing took 8 hours and utilised only a full wheelbarrow of wood. The experience was filled with joy and excitement because this was a highly experimental endeavour and the results were an economical bisque firing. Cones were placed throughout the kiln, indicating an even temperature was achieved throughout.
The second firing was a glaze firing Cone 11 1300°Celcius. This firing process took approximately 12 hours and utilised a substantial amount of wood, approximately two-thirds of a Ute load. The kiln achieved Cone 8 using natural draft of the chimney but then seemed to stall so necessitating the use of a small battery blower for the final hours to attain the desired temperature of 1300° C.
Subsequently, three more stoneware firings have been conducted, ranging in duration from 10 to 14 hours and a flattened Cone 11 1320° C has been achieved. These firings yielded remarkable results, considering the relatively short duration of the wood firing process.
Daniel attributes this to the enhanced ash deposits achieved with the absence of a bag wall and the utilisation of the stammer wall in the back to direct the flame upwards. This modification allowed for increased flame activity and direct ash deposits on the work. The light brick construction facilitates economic benefits and enables the attainment of high temperatures with relative ease.
Small kilns like this offer potters increased accessibility to wood firing due to their low fuel consumption, short firing times, and rapid turnaround. Consequently, they serve as a valuable test kiln and educational tool for glaze research and gaining insights into wood firing techniques.
If constructing a kiln from scratch, the kiln would like a larger and deeper firebox, larger flues, and a larger chimney. However, given the constraints and resources available, Daniel is content with the outcomes achieved with this kiln and the firings conducted.
We would like to thank our daughter Alice for her assistance and advice in the metalwork construction and welding required to transform ‘this old piece of rusty junk’ as she puts it! into a viable wood firing kiln. Thanks to the small team of kiln helpers as wood firing is always an arduous endeavour and kiln shelves need washing, props need dipping, wadding is required and a pains taking packing is still necessary. So, thanks for my helpers – now I only need one other person! Siena Hyland and Mila Folsom have both been involved. Thanks to assistance from my partner Gabrielle Powell who helped to write this article and promotes our workshop. All in all, this kiln is a great asset to Bandicoot Pottery and we look forward to future wood firing endeavours in it.





Comments